Variable frequency drive technical article workspace

The $12 Switch Swap That Cost Me $1,150

By Pavel Novak

November 2021. A Friday night call from our building manager: half the third-floor conference rooms had dead outlets. My first thought wasn't "call an electrician." It was "I can fix this myself and save the company $150."

That decision cost us roughly $1,150 and a weekend I still complain about at cookouts. Not because anything caught fire, but because I broke one of my own rules: no unplanned electrical work after 5 PM on a Friday.

Friday Night: The "Simple" Diagnosis

I've been handling facility maintenance orders for 11 years now. I've personally made — and documented — 23 significant mistakes, totaling roughly $9,600 in wasted budget. After the third one (a $420 shipping error on the wrong bollard lights in 2017), I built a pre-job checklist. My team uses it. I told myself I'd use it too.

Friday night, I didn't.

The setup: a tenant had plugged a space heater and a coffee maker into the same circuit, tripped a breaker, and something in the switch loop burned out. Two of the three switches in that zone were dead. One was a three-way leg that controlled the hallway lights.

Conventional wisdom says call a licensed electrician for anything beyond swapping a single-pole switch. My experience — 11 years, dozens of switch replacements — said I could handle it. Calculated the worst case: I mess up a $12 switch and buy another one. Best case: save $150. The expected value said go for it. The downside felt trivial.

That's the thing about risk. You usually miscalculate it at the exact moment you feel most confident.

Saturday Morning: The Install That Looked Fine

I went to the hardware store at 7 AM. Picked up a Leviton 3-way switch for the hallway leg, plus a couple of single-pole Leviton switches for the simpler replacements. Total: $52 with the wire nuts and tape.

Back at the building by 8. Cut the breaker. Pulled the old switches. And here's where I made my first real mistake: I didn't pull up a leviton light switch wiring diagram single pole reference on my phone. I'd done this dozens of times, right? Line, load, ground, brass screw, silver screw. Simple.

But the three-way leg was a different animal. I mixed up one of the traveler wires with the common wire. On a leviton 3 way switch installation, the common terminal is typically the darker screw, and the two travelers are brass. I had it in my head that the dark screw was for the hot line. It's not — it's for the common leg.

Everything looked fine when I flipped the breaker. The lights turned on. Great. I moved on to the other switches, felt smug about the $52 I'd spent instead of $200, and went to lunch.

Saturday Afternoon: The Snowball

The problem surfaced around 2 PM when a tenant called to say the hallway lights wouldn't turn off from one end of the hall. The switch worked from one position but not the other. Classic traveler mix-up.

I went back up, opened the box again, and this time I pulled up the actual diagram on my phone. The correction took four minutes. But by then I'd already lost the afternoon, and I was annoyed at myself for not looking it up the first time.

Then I remembered the generator test.

We have a backup generator with a 50 amp plug connection — NEMA 14-50R, standard for that size of unit — that's supposed to be load-tested monthly. I'd skipped October because I'd been slammed on a remodel project. So I figured I'd knock it out Saturday afternoon.

The generator with 50 amp plug wouldn't start. Battery dead. Not just low — dead dead. And when I pulled the plug to check the terminals, they were oxidized green.

So now I'm standing in the mechanical room at 4 PM on a Saturday with a light switch I have to re-open and a generator with a dead battery and corroded connections.

I grabbed a Vector smart battery charger from the shop. It's a decent unit — has a reconditioning mode that's supposed to recover sulfated batteries. I hooked it up, set it to AGM mode (which turned out to be wrong — the generator uses a flooded lead-acid battery), and left it overnight.

That was mistake number three. The reconditioning mode on a flooded battery isn't going to cause a fire, but it doesn't do much good either. And overnight, the charger didn't restore a battery that was already past its service life. It was a 2019 battery. It owed us nothing.

Sunday Morning: The Last Straw

Sunday morning, I came back to the building early. I figured I'd test the generator again, and if the battery was still dead, I'd call our maintenance supplier Monday and eat the cost.

But first, I wanted to knock out one more thing on my list: the push mower we use for the small grass strips near the loading dock. It had been running rough since October. I figured I'd pull the spark plug, clean it, and call it done.

If you've ever wondered how to remove broken spark plug from an aluminum cylinder head, the answer is: very carefully, with the engine cold, and with penetrating oil. I did none of those things.

The engine was warm from the idle test. I didn't use oil. And I torqued that plug with a 3/8 ratchet and a bad attitude. The plug came out — but the threaded shell stayed in the head.

I stood there in the loading dock, holding a ceramic insulator and a length of wire, staring at the hole where the rest of the plug used to be. That's when I finally called the electrician.

Sunday Night: The Electrician's Walk-Through

He showed up at 6 PM. Weekend emergency rate: $380, plus $60 for parts (a dimmer on the same circuit had failed from the original tenant overload).

He fixed the three-way in about 15 minutes. Then he looked at the generator and the mower.

Generator: new battery needed. $240, plus he recommended cleaning the terminals and applying dielectric grease. Which I could have done myself if I hadn't been in a hurry.

Mower: he extracted the broken plug shell with a thread chaser and a shop vac, then re-tapped the threads. $95 for that plus a new plug. He was nice about it, which somehow made it worse.

The Tally

Here's what that weekend actually cost:

  • Leviton switches and supplies: $52
  • Weekend emergency electrician: $440 (including the replacement dimmer)
  • Generator battery: $240
  • Vector smart battery charger (the old one gave out mid-weekend — I replaced it): $95
  • Spark plug extraction and new plug: $95
  • Two extra hardware store runs: $30 in gas and miscellaneous

Total: roughly $1,150.

The original quote from our regular electrician for the switch work was $180. I saved $128 on the switch job and spent $970 extra on everything else.

That's what I mean when I say TCO isn't just about the invoice. The sticker price for DIY was $52. The total cost of ownership — including my time, the emergency call, the battery I would have needed anyway (but would have bought on a weekday at 30% less), and the tools I couldn't return — was six figures, in hours, and four figures in dollars.

What I Actually Learned (and Wrote Down)

Three things made it into the checklist after that weekend:

One: weekend electrical work of any kind requires a photo of the wiring before you pull the old switch. That's not about skill. It's about avoiding the one mistake that turns a 15-minute job into a return trip.

Two: the generator gets load-tested on the first Monday of every month, period. Battery health and terminal condition get checked at the same time. The generator with 50 amp plug setup isn't complicated, but it fails silently if you ignore it.

Three: cold engines and broken plugs don't mix. If the plug won't turn by hand with a cold engine and penetrating oil, it comes to the shop. That lesson cost me $95 and a chunk of Sunday morning I'll never get back.

The real math, though, is simpler than all that. My time — if you value it at a modest $65 an hour, which is roughly what the company bills for facility work — is worth more than $52. Anytime I "save money" by doing something myself on a weekend, I'm spending at least $130 an hour. That's not TCO thinking. That's a hobby that happens to cost the company money.

The switch was fine. The Leviton switch does exactly what it's supposed to do. The generator battery was just old. The spark plug was in the wrong hands — mine.

Everything I'd read about auto-retail and home maintenance said the savings from DIY were real. And they are, for the right projects. But the conventional wisdom doesn't account for the second trip to the hardware store, the emergency call you finally make at 6 PM on Sunday, or the battery you could have bought on sale on Tuesday instead of full-price on Saturday afternoon.

Total cost isn't the price tag. It's the price tag, plus the weekend, plus the things you broke that you weren't planning to fix, plus the time you spent not doing your actual job.

I still do my own switch work. But now I look at the diagram first, and I look at the calendar before I look at the tool bag.

Share this technical note with your project team.
Pavel Novak

Pavel Novak

Pavel Novak is a generator and backup-power analyst specializing in standby, portable, diesel, gas, inverter, and commercial generating sets with transfer equipment. For reciprocating-engine sets, he applies ISO 8528-5 dynamic-performance criteria and IEC 60034-1 generator ratings to load steps, starting current, voltage and frequency recovery, cooling, and output; for transfer equipment, he uses IEC 60947-6-1 requirements. He helps facility teams and buyers select systems around emergency loads, runtime, commissioning, fuel strategy, service access, operating cost, and resilience.